Geri Dön

FG 121.111 - MOVING PARTS Yedek Parça ve Yedek Parça Fiyatları - Santana Otomotiv

№- Name A* Part number A Part number, Price per Unit., $

CRANKSHAFT		 - XXX XXX XXX XXXX - -
CRANKSHAFT WITH
COUNTERWEIGHT, FLYWHEEL, CRANKSHAFT BEARING SHELLS AND CONNECTING ROD BEARING SHELLS MAKE GLYCO OPTIONAL		 001 A 62 103 019 01  - -
CRANKSHAFT WITH
COUNTERWEIGHT, FLYWHEEL, CRANKSHAFT BEARING SHELLS AND CONNECTING ROD BEARING SHELLS MAKE LAUCHERTHAL OPTIONAL		 001 A 62 103 020 01  - -
001 CRANKSHAFT WITH
COUNTERWEIGHT AND FLYWHEEL		 001 A 62 103 011 01  - -
002 SHIM, 5.45 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT		 001 A 18 003 100 52  - -
SHIM, 5.60 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT		 001 A 18 003 101 52  - $24.04
SHIM, 5.75 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT		 001 A 18 003 102 52  - $24.04
SHIM, 5.90 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT		 001 A 18 003 103 52  - -
SHIM, 6.05 MM THICK
OPTIONAL FOR CRANKSHAFT GEAR AT CRANKSHAFT		 001 A 18 003 104 52  - -
003 WOODRUFF KEY
ON CRANKSHAFT, FRONT 5 X 7,5 DIN 6888		 001 - -
004 CRANKSHAFT GEAR
ON CRANKSHAFT, FRONT		 001 A 18 005 202 03  - -
005 OIL SLINGER RING
ON CRANKSHAFT, FRONT		 001 A 18 003 104 25  - -
05a COUNTERWEIGHT 001 A 12 103 103 07  - -
05b SPACER RING
FOR CRANKSHAFT, OIL SLINGER RING		 001 A 12 103 100 51  - -
006 CYLINDRICAL PIN
8 H8 X 8 DIN 7 FOR COUNTERWEIGHT AT CRANKSHAFT		 001 - -
007 CYLINDRICAL PIN
8 H8 X 16 DIN 7 FOR COUNTERWEIGHT AT CRANKSHAFT		 001 - -
008 FLYWHEEL WITH 001 A 62 103 003 05  - -
009 STARTER RING 001 A 62 103 201 05  - -
010 NECKED-DOWN BOLT
FOR FLYWHEEL AT CRANKSHAFT		 006 A 12 103 106 71  - -
011 CYLINDRICAL PIN
10 H8 X 18 DIN 7 FOR FLYWHEEL AT CRANKSHAFT		 001 - -
013 COLLAR SCREW 001 A 18 603 102 71  - -
014 SEALING RING
AT CRANKSHAFT, FRONT		 001 A 12 003 101 81  - -
14a ADJUSTING NEEDLE
FOR TOP DEAD CENTER ADJUSTMENT		 001 A 12 103 200 15  - $6.56
PIN AT CYLINDER CRANKCASE 001 A 62 103 200 74  - -
015 PULLEY
DIA. 122 MM UP TO ENGINE		 001 A 12 120 001 05  - $234.91
PULLEY
DIA. 135 MM FROM ENGINE		 001 A 62 120 001 05  - -
016 ANNULAR GROOVED BEARING
6202 DIN 625 FOR DRIVE SHAFT AT CRANKSHAFT		 001 - -
017 LOCKING RING
FOR DRIVE SHAFT AT CRANKSHAFT		 001 A 18 603 100 33  - -
018 FABRIC SEALING RING
75 X 87 X 6 GL N 255 A FOR CRANKSHAFT SEALING IN CYLINDER CRANKCASE, REAR		 001 - -

CRANKSHAFT BEARING		 - XXX XXX XXX XXXX - -
020 SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 70-MM = STANDARD (MAKE GLYCO) OPTIONAL READY FOR INSTALLATION		 001 A 12 103 005 97  - -
SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 70-MM = STANDARD (MAKE LAUCHERTHAL) OPTIONAL READY FOR INSTALLATION		 001 A 62 103 000 97  - -
SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 70-MM = STANDARD (MAKE VANDERVELL) OPTIONAL READY FOR INSTALLATION		 001 A 12 103 010 97  - -
021 CRANKSHAFT BEARING SHELL
MAKE GLYCO WITH GROOVE;USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER BE		 004 A 12 103 314 01  - -
CRANKSHAFT BEARING SHELL
MAKE LAUCHERTHAL WITH GROOVE;USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CEN		 004 A 62 103 300 01  - -
CRANKSHAFT BEARING SHELL
MAKE VANDERVELL WITH GROOVE;USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENT		 004 A 12 103 319 01  - -
022 CRANKSHAFT BEARING SHELL
MAKE GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL		 002 A 12 103 314 02  - -
CRANKSHAFT BEARING SHELL
MAKE LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL		 002 A 62 103 300 02  - -
CRANKSHAFT BEARING SHELL
MAKE VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL		 002 A 12 103 319 02  - -
SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.75-MM = REPAIR SIZEI MAKE GLYCO OPTIONAL READY FOR INSTALLATION		 001 A 12 103 006 97  - -
SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.75-MM = REPAIR SIZE I MAKE LAUCHERTHAL OPTIONAL READY FOR INSTALLATION		 001 A 62 103 001 97  - -
SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.75-MM = REPAIR SIZE I MAKE VANDERVELL OPTIONAL READY FOR INSTALLATION		 001 A 12 103 011 97  - -
CRANKSHAFT BEARING SHELL,
MAKE GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING; USED AS UPPER AND LOWER HALF FOR CENTER B		 004 A 12 103 315 01  - -
CRANKSHAFT BEARING SHELL,
MAKE LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING; USED AS UPPER AND LOWER HALF FOR CE		 004 A 62 103 301 01  - -
CRANKSHAFT BEARING SHELL,
MAKE VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING; USED AS UPPER AND LOWER HALF FOR CEN		 004 A 12 103 320 01  - -
CRANKSHAFT BEARING SHELL,
MAKE GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL		 002 A 12 103 315 02  - -
CRANKSHAFT BEARING SHELL,
MAKE LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL		 002 A 62 103 301 02  - -
CRANKSHAFT BEARING SHELL,
MAKE VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL		 002 A 12 103 320 02  - -
SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.50-MM=REPAIR SIZE II MAKE GLYCO OPTIONAL READY FOR INSTALLATION		 001 A 12 103 007 97  - -
SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.50-MM=REPAIR SIZE II MAKE LAUCHERTHAL OPTIONAL READY FOR INSTALLATION		 001 A 62 103 002 97  - -
SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.50-MM=REPAIR SIZE II MAKE VANDERVELL OPTIONAL READY FOR INSTALLATION		 001 A 12 103 012 97  - -
CRANKSHAFT BEARING SHELL,
MAKE GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B		 004 A 12 103 316 01  - -
CRANKSHAFT BEARING SHELL,
MAKE LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CE		 004 A 62 103 302 01  - -
CRANKSHAFT BEARING SHELL,
MAKE VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CEN		 004 A 12 103 321 01  - -
CRANKSHAFT BEARING SHELL,
MAKE GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL		 002 A 12 103 316 02  - -
CRANKSHAFT BEARING SHELL,
MAKE LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL		 002 A 62 103 302 02  - -
CRANKSHAFT BEARING SHELL,
MAKE VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL		 002 A 12 103 321 02  - -
SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.25-MM = REPAIR SIZE III MAKE GLYCO READY FOR INSTALLATION		 001 A 12 103 008 97  - -
SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.25-MM=REPAIR SIZE III MAKE LAUCHERTHAL READY FOR INSTALLATION		 001 A 62 103 003 97  - -
SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.25-MM=REPAIR SIZE III MAKE VANDERVELL READY FOR INSTALLATION		 001 A 12 103 013 97  - -
CRANKSHAFT BEARING SHELL,
MAKE GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING; USED AS UPPER AND LOWER HALF FOR CENTER B		 004 A 12 103 317 01  - -
CRANKSHAFT BEARING SHELL,
MAKE LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING; USED AS UPPER AND LOWER HALF FOR CE		 004 A 62 103 303 01  - -
CRANKSHAFT BEARING SHELL,
MAKE VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING; USED AS UPPER AND LOWER HALF FOR CEN		 004 A 12 103 322 01  - -
CRANKSHAFT BEARING SHELL,
MAKE GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL		 002 A 12 103 317 02  - -
CRANKSHAFT BEARING SHELL,
MAKE LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL		 002 A 62 103 303 02  - -
CRANKSHAFT BEARING SHELL,
MAKE VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL		 002 A 12 103 322 02  - -
SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.00-MM = REPAIR SIZE IV, MAKE GLYCO OPTIONAL READY FOR INSTALLATION		 001 A 12 103 009 97  - -
SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.00-MM = REPAIR SIZE IV MAKE LAUCHERTHAL OPTIONAL READY FOR INSTALLATION		 001 A 62 103 004 97  - -
SET OF
CRANKSHAFT BEARING SHELLS, INTERIOR DIA. 69.00-MM = REPAIR SIZE IV MAKE VANDERVELL OPTIONAL READY FOR INSTALLATION		 001 A 12 103 014 97  - -
CRANKSHAFT BEARING SHELL,
MAKE GLYCO WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CENTER B		 004 A 12 103 318 01  - -
CRANKSHAFT BEARING SHELL,
MAKE LAUCHERTHAL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CE		 004 A 62 103 304 01  - -
CRANKSHAFT BEARING SHELL
MAKE VANDERVELL WITH GROOVE; USED AS UPPER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING, USED AS UPPER AND LOWER HALF FOR CEN		 004 A 12 103 323 01  - -
CRANKSHAFT BEARING SHELL,
MAKE GLYCO WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL		 002 A 12 103 318 02  - -
CRANKSHAFT BEARING SHELL,
MAKE LAUCHERTHAL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL		 002 A 62 103 304 02  - -
CRANKSHAFT BEARING SHELL
MAKE VANDERVELL WITHOUT GROOVE; USED AS LOWER HALF FOR 1ST AND 3RD CRANKSHAFT BEARING OPTIONAL		 002 A 12 103 323 02  - -

CONNECTING ROD		 - XXX XXX XXX XXXX - -
025 CONNECTING ROD 004 A 62 103 005 20  - -
026 CONNECTING ROD BUSHING 004 A 62 103 800 50  - $17.90
027 CONNECTING SCREW 008 A 12 103 803 71  - $27.27
028 NUT 008 A 18 203 800 72  - $8.73
CONNECTING ROD
BUSHING, EXTERIOR DIA. 29.5-MM REPAIR DESIGN		 004 A 62 103 801 50  - $32.08
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 52.00-MM = STANDARD MAKE GLYCO OPTIONAL
Replaced by: A  121 038 28 10		 - A 12 103 828 11  - -
029 CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 52.00-MM = STANDARD MAKE GLYCO OPTIONAL		 008 A 12 103 828 10  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 52.00-MM = STANDARD MAKE LAUCHERTHAL OPTIONAL
Replaced by: A  121 038 07 10		 - A 12 103 807 11  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 52.00-MM = STANDARD MAKE LAUCHERTHAL OPTIONAL		 008 A 12 103 807 10  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 52.00-MM = STANDARD MAKE VANDERVELL OPTIONAL		 008 A 12 103 833 10  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.75-MM = REPAIR SIZE I MAKE GLYCO OPTIONAL
Replaced by: A  121 038 29 10		 - A 12 103 829 11  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.75-MM = REPAIR SIZE I MAKE GLYCO OPTIONAL		 008 A 12 103 829 10  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.75-MM = REPAIR SIZE I MAKE LAUCHERTHAL OPTIONAL
Replaced by: A  121 038 08 10		 - A 12 103 808 11  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.75-MM = REPAIR SIZE I MAKE LAUCHERTHAL OPTIONAL		 008 A 12 103 808 10  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.75-MM = REPAIR SIZE I MAKE VANDERVELL OPTIONAL		 008 A 12 103 834 10  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.50-MM = REPAIR SIZE II MAKE GLYCO OPTIONAL
Replaced by: A  121 038 30 10		 - A 12 103 830 11  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.50-MM = REPAIR SIZE II MAKE GLYCO OPTIONAL		 008 A 12 103 830 10  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.50-MM = REPAIR SIZE II MAKE LAUCHERTHAL OPTIONAL
Replaced by: A  121 038 09 10		 - A 12 103 809 11  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.50-MM = REPAIR SIZE II MAKE LAUCHERTHAL OPTIONAL		 008 A 12 103 809 10  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.50-MM = REPAIR SIZE II, MAKE VANDERVELL OPTIONAL		 008 A 12 103 835 10  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.25-MM = REPAIR SIZE III OPTIONAL
Replaced by: A  121 038 31 10		 - A 12 103 831 11  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.25-MM = REPAIR SIZE III OPTIONAL		 008 A 12 103 831 10  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.25-MM = REPAIR SIZE III MAKE LAUCHERTHAL OPTIONAL
Replaced by: A  121 038 10 10		 - A 12 103 810 11  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.25-MM = REPAIR SIZE III MAKE LAUCHERTHAL OPTIONAL		 008 A 12 103 810 10  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.25-MM = REPAIR SIZE III MAKE VANDERVELL OPTIONAL		 008 A 12 103 836 10  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.00-MM = REPAIR SIZE IV MAKE GLYCO OPTIONAL
Replaced by: A  121 038 32 10		 - A 12 103 832 11  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.00-MM = REPAIR SIZE IV MAKE GLYCO OPTIONAL		 008 A 12 103 832 10  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.00-MM = REPAIR SIZE IV MAKE LAUCHERTHAL OPTIONAL
Replaced by: A  121 038 11 10		 - A 12 103 811 11  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.00-MM = REPAIR SIZE IV MAKE LAUCHERTHAL OPTIONAL		 008 A 12 103 811 10  - -
CONNECTING ROD
BEARING SHELL HALF, INTERIOR DIA. 51.00-MM = REPAIR SIZE IV, MAKE VANDERVELL OPTIONAL		 008 A 12 103 837 10  - -

PISTON		 - XXX XXX XXX XXXX - -
PISTON WITH
PISTON PIN AND PISTON RINGS FOR CYLINDER DIA. 85.00-MM = STANDARD
Replaced by: A  621 030 21 17		 - A 62 103 010 17  - -
034 PISTON WITH
PISTON PIN AND PISTON RINGS FOR CYLINDER DIA. 85.00-MM = STANDARD		 004 A 62 103 021 17  - -
035 COMPRESSION RING
FOR PISTON GROOVE I		 004 A 00 103 779 16  - -
036 COMPRESSION RING
FOR PISTON GROOVE II AND III		 008 A 00 103 784 16  - -
038 PC-OIL SLOTTED RING
FOR PISTON GROOVE IV		 004 A 00 103 774 18  - -
039 PISTON PIN 004 A 62 103 700 20  - -
040 WIRE SNAP RING 008 A 00 099 425 35  - -
PISTON WITH
PISTON PIN AND PISTON RINGS, FOR CYLINDER DIA. 85.25-MM = REPAIR SIZE I
Replaced by: A  621 030 22 17		 - A 62 103 011 17  - -
PISTON WITH
PISTON PIN AND PISTON RINGS, FOR CYLINDER DIA. 85.25-MM = REPAIR SIZE I		 004 A 62 103 022 17  - -
COMPRESSION RING
FOR PISTON GROOVE I		 004 A 00 103 780 16  - -
COMPRESSION RING
FOR PISTON GROOVE II AND III		 008 A 00 103 785 16  - -
PC-OIL SLOTTED RING
FOR PISTON GROOVE IV		 004 A 00 103 775 18  - -
PISTON PIN 004 A 62 103 700 20  - -
WIRE SNAP RING 008 A 00 099 425 35  - -
PISTON WITH
PISTON PIN AND PISTON RINGS, FOR CYLINDER DIA. 85.50-MM = REPAIR SIZE II
Replaced by: A  621 030 23 17		 - A 62 103 012 17  - -
PISTON WITH
PISTON PIN AND PISTON RINGS, FOR CYLINDER DIA. 85.50-MM = REPAIR SIZE II		 004 A 62 103 023 17  - -
COMPRESSION RING
FOR PISTON GROOVE I		 004 A 00 103 781 16  - -
COMPRESSION RING
FOR PISTON GROOVE II AND III		 008 A 00 103 786 16  - -
PC-OIL SLOTTED RING
FOR PISTON GROOVE IV		 004 A 00 103 776 18  - -
PISTON PIN 004 A 62 103 700 20  - -
WIRE SNAP RING 008 A 00 099 425 35  - -
PISTON WITH
PISTON PIN AND PISTON RINGS, FOR CYLINDER DIA. 86.00-MM = REPAIR SIZE III
Replaced by: A  621 030 24 17		 - A 62 103 013 17  - -
PISTON WITH
PISTON PIN AND PISTON RINGS, FOR CYLINDER DIA. 86.00-MM = REPAIR SIZE III		 004 A 62 103 024 17  - -
COMPRESSION RING
FOR PISTON GROOVE I		 004 A 00 103 782 16  - -
COMPRESSION RING
FOR PISTON GROOVE II AND III		 008 A 00 103 787 16  - -
PC-OIL SLOTTED RING
FOR PISTON GROOVE IV		 004 A 00 103 777 18  - -
PISTON PIN 004 A 62 103 700 20  - -
WIRE SNAP RING 008 A 00 099 425 35  - -
PISTON WITH
PISTON PIN AND PISTON RINGS FOR CYLINDER DIA. 86.50-MM = REPAIR SIZE IV
Replaced by: A  621 030 25 17		 - A 62 103 014 17  - -
PISTON WITH
PISTON PIN AND PISTON RINGS FOR CYLINDER DIA. 86.50-MM = REPAIR SIZE IV		 004 A 62 103 025 17  - -
COMPRESSION RING
FOR PISTON GROOVE I		 004 A 00 103 783 16  - -
COMPRESSION RING
FOR PISTON GROOVE II AND III		 008 A 00 103 788 16  - -
PC-OIL SLOTTED RING
FOR PISTON GROOVE IV		 004 A 00 103 778 18  - -
PISTON PIN 004 A 62 103 700 20  - -
WIRE SNAP RING 008 A 00 099 425 35  - -
* In the column 'A' indicates the number that is used in the selected vehicle.
- To find out where to buy the item or equivalent, click on the part number.